Can I insulate the floors in my home?

Share

X
Facebook
LinkedIn
Email

Sandra Hayes

If you live in a home built prior to 1990 the chances are that it will not have any floor insulation. This can result in heat loss of between 10 and 20% depending on the age of the property and the floor type. This not only results it higher energy bills, but also floors that feel cold on the feet and draughty in the winter months. Particularly badly affected are rooms above unheated garages, basements, or driveways.  

If you’ve had an EPC for your home and it recommends floor insulation you maybe wondering where to start.  In this blog we will provide you with some guidance, where to go for further information and how to go about finding an installer.

Floor type

The first step when considering floor insulation is establishing how the ground floor in your home has been constructed. Prior to the 1950’s it was common for homes to have suspended timber floors, although many of these homes also have solid floors at the rear where the cooking and washing was done. To avoid issues with damp and rot, suspended timber floors have a void beneath the joists, with air bricks in the external walls to allow a flow of air beneath the floor.  On no account should these air bricks be blocked up to reduce draughts – it will only cause expensive damp problems later.

Homes built after the 1950’s are more likely to have floors made from concrete (sometimes with steel) although there are difference construction techniques, including slabs sitting directly on the ground with block and beam.  Block and beam floors will have a void underneath like a suspended timber floor. However, for practical purposes (i.e., the difficulty of gaining access to the void through the concrete) these are treated in the same way as a solid floor.

Suspended timber floors

The options available for the insulation of a suspended timber floor depend on the depth of the void between the ground and the bottom of the joists, which can vary between 1m and 250mm. If the void is deep enough the insulation can be done by cutting a hole through the floorboards and insulating from below. If the space is big enough a person can get underneath and insulate using a mineral wool insulation material held in place using netting nailed to the underside of the joists. One company specialising in this approach is Sapwells who are based in Milton Keynes.

If space does not allow for this approach, but there is still a void of at least 200mm, an alternative solution is offered by Q-Bot who use a remotely controlled robot to spray insulation under the floor boards. Both options can be installed with minimal disruption to the household. 

A third option for suspended timber floors is to install the insulation from above. However, this option is more disruptive as it involves lifting all the floorboards and potentially replacing some or all of them if they are damaged in the process. Once the joists are exposed in this way, brackets or netting can be attached to the joists to hold the insulation in place. 

The insulation material can be mineral wool, cellulose, sheep’s wool, hemp, or a PIR insulation board. The latter requires very careful cutting to avoid leaving gaps between the insulation and the joists or the insulation and the wall, possibly resulting in cold spots, liable to condensation and mould. PIR also has the disadvantage of not being vapour permeable meaning that extra care needs to be taken to ensure that there is good ventilation, avoiding a build-up of moisture in the floor.

Solid floors

If you have a solid floor or a floor with an inaccessible/shallow void, your only option is to put insulation on top of the existing floor. This can be done by laying a damp proof membrane on the existing floor, placing rigid insulation boards on top and finishing off with chipboard flooring boards. The downside of this is that doors will need to be trimmed to make them shorter and some sockets and skirting boards may need to be moved, as well as fixtures and fittings like kitchen units, baths, toilets etc. The best time to get this work done is therefore going to be when other work (like the fitting of a new kitchen) is being done. This is also the best time to install internal wall insulation if your home has solid walls and there are reasons why you can’t externally insulate (like living in a Conservation Area).  

Another potential issue is the loss of room height.  To comply with the Building Regulations, you will need at least 70mm of PIR insulation.  Once the chipboard is added you could easily to be looking at a loss of room height of 100mm.  While not an issue for rooms with ceiling heights 2.5m plus, it is an issue when the existing ceiling height is already low, as can be the case in kitchens and bathrooms. For such rooms, an aerogel product (made from blown silicon) is the best option, as it provides better thermal performance at a lower thickness – albeit at a much higher cost.

Further information

Further information and useful images can be found on the Energy Saving Trust, Eco Home Essentials and Which? websites. More in depth information on suspended timber floor insulation (targeted at suppliers and installers) can be found in the Government’s best practice guide.

Installers

If you are looking for an installer of floor insulation we suggest looking for a member of the National Insulation Association and/or TrustMark.  Installers approved by Trading Standards for listing on Buy with Confidence are also worth considering.

Taking a whole house approach

If you are contemplating floor insulation it makes sense to consider whether there are other areas of your home that would benefit from insulation as a part of a whole house approach.  This means checking if the walls are insulated and if you have sufficient loft insulation (if it’s mineral wool this means having insulation with a depth of at least 270mm). If your home was built before the 1930’s, it is likely to have solid walls which will not be insulated; if it has a cavity wall construction and was built before the mid 1980’s it may have no or limited amounts of insulation, unless it has been retrofitted.  You will also need to consider ensuring that your home has adequate ventilation when insulation is being installed as this will make it more airtight.

If you would like help and advice on the best options to make your home more energy efficient, before making any concrete decisions, then a Whole House Retrofit Plan from our SuperHomes team would be the right option for you.  Further information about this service offer can be found here.

Recommended for you

New: Find out more about NEF's Impact

Discover the difference we're making in National Energy Foundation's latest Impact Report. See how we're creating positive change in energy efficiency and sustainability.

National Energy Foundation
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.